Science Lab Guides

PhET Ohm’s Law Lab: A Guided Simulation Activity for High School

PhET Ohm's Law Lab: A Guided Simulation Activity for High School

The PhET Ohm’s Law lab is one of the quickest ways to make V = IR feel real. Instead of memorizing a triangle, students move two sliders, watch the current change, and discover the relationship from their own data. The free simulation from the University of Colorado Boulder runs in any browser, so it works on Chromebooks, laptops and the projector.

This guide turns the simulation into a complete 45–55 minute lesson for high school physics or physical science: a prediction warm-up, two controlled experiments, a data table, a graphing task and discussion questions. If your class has already used the Circuit Construction Kit lab, this is a natural follow-up because it isolates one relationship at a time.

In this guide11 sections
  1. What students see in the simulation
  2. Learning goals
  3. Warm-up: make a prediction (5 minutes)
  4. Experiment 1: change the voltage
  5. Experiment 2: change the resistance
  6. Sample data table
  7. Graphing the relationship
  8. Discussion questions
  9. Differentiation and extensions
  10. Frequently asked questions
  11. Bringing it together

What students see in the simulation

The Ohm’s Law simulation shows the equation V = IR at the top, a simple circuit with batteries and a resistor, and two sliders: one for voltage and one for resistance. When students change a slider, the letters in the equation grow or shrink to show how each quantity changes, and the current readout (in milliamps) updates instantly. The number of batteries in the picture changes with the voltage, and the dots inside the resistor become denser as resistance rises.

Before class, open the simulation yourself and note the slider ranges on the version your students will use, so your data table steps fit inside them.

Learning goals

  • Describe how current changes when voltage increases and resistance stays constant.
  • Describe how current changes when resistance increases and voltage stays constant.
  • Use data and a graph to support the equation V = IR.
  • Convert milliamps to amps and calculate resistance from measured values.

Warm-up: make a prediction (5 minutes)

Start with a short bell ringer: “A flashlight uses two batteries. If you add a third battery, what happens to the current in the bulb? Why?” Have students write a one-sentence prediction and a reason. Collect a few answers aloud without correcting them yet. The goal is to surface ideas you will test.

Experiment 1: change the voltage

  1. Set the resistance slider to a round value, such as 500 Ω, and leave it there.
  2. Set the voltage to the lowest whole number available, then increase it one volt at a time.
  3. Record the current in mA for each voltage.
  4. Describe the pattern in one sentence before moving on.

Experiment 2: change the resistance

  1. Set the voltage to a fixed value, such as 6.0 V.
  2. Set resistance to 100 Ω and record the current.
  3. Increase resistance in equal steps (200, 300, 400 Ω and so on) and record each current.
  4. Compare what happens when resistance doubles from 200 to 400 Ω.

Sample data table

Give students a table like this. The “calculated R” column checks whether V ÷ I really gives back the resistance on the slider.

Trial Voltage (V) Resistance (Ω) Current (mA) Current (A) Calculated R = V ÷ I (Ω)
1 2.0 500
2 4.0 500
3 6.0 500
4 6.0 200
5 6.0 400
6 6.0 800

Students should find, for example, that 6.0 V across 500 Ω gives 12 mA (0.012 A), and 6.0 ÷ 0.012 = 500 Ω. Seeing the calculation match the slider is a satisfying moment for many students.

Graphing the relationship

Graph 1: current vs. voltage

Plot voltage on the x-axis and current (A) on the y-axis for the constant-resistance trials. The points should form a straight line through the origin. Ask: “What does the slope of this line represent?” The slope is 1/R, so a steeper line means a smaller resistance.

Graph 2: current vs. resistance

Plot resistance on the x-axis and current on the y-axis. This graph curves downward: doubling resistance halves the current. Stronger classes can plot current against 1/R to straighten the curve, which is a useful introduction to linearizing data.

Discussion questions

  • Which quantity is the independent variable in each experiment? Which is held constant?
  • If voltage triples and resistance stays the same, what happens to current?
  • Why might a real resistor not follow Ohm’s law perfectly when it gets hot?
  • A phone charger supplies 5 V. If the circuit has 250 Ω of resistance, what is the current?
  • Go back to your warm-up prediction. Was it correct? What evidence supports your answer now?

Differentiation and extensions

  • Support: give students a partially filled table and sentence frames such as “When voltage increases, current ___ because ___.”
  • Challenge: ask students to design their own trial that produces exactly 10 mA, then test it.
  • Connect: build the same values with the Circuit Construction Kit and compare the ammeter reading to this simulation.
  • Review: finish with a quick round from our review games list or an exit ticket asking for one calculation and one explanation.

Frequently asked questions

Is the PhET Ohm’s Law simulation free?

Yes. PhET simulations are free to use from the PhET website at the University of Colorado Boulder, and the HTML5 version runs in a browser without installing anything.

What grade level is this lab for?

It fits grades 8–12. Middle school classes can stop after the two experiments and the pattern sentences; high school physics classes should complete both graphs and the calculations.

How long does the lab take?

Plan about 45–55 minutes: 5 minutes for the warm-up, 20 minutes for data collection, 15 minutes for graphing and 10 minutes for discussion. Graphing can move to homework if time is short.

What should students already know?

Students only need the basic idea of a circuit and the units volt, ohm and amp. The lab is designed so they discover the relationship rather than being told it first.

Bringing it together

A good Ohm’s law lesson leaves students able to explain the relationship, not just plug numbers into a formula. With two controlled experiments, a table and two graphs, this PhET lab gives them the evidence to do that. For more ready-made simulation lessons, browse our classroom simulations page.